Find the relevant trade package or installation support. The original 22 documented subjects remain available; two complementary services are identified separately without an individual brochure. Scope, responsibility and resources are agreed for each project.
24 services in the catalogue
Ædra describes execution, installation support and coordination. Design responsibility, classifications, approvals and licensed installations remain with the responsible specialist parties unless otherwise documented and contracted.
Firestopping, fire-rated joints, insulation of services and building elements under specified systems.
Fire-related work is scoped against approved systems, with project responsibility and inspection assigned.
Sealing pipe and cable penetrations through fire-separating walls and slabs, including linear joints, to a specified firestopping system.
Cable and pipe penetrations; fire-rated linear joints; closure against approved details
Fire design and classification remain with responsible specialists; installation records are agreed.
Insulation of pipes and ducts using specified materials and thicknesses, preformed shells, restraints and continuous joints.
Pipe and technical services insulation; specified thickness, jackets and joints
Fire-related work is scoped against approved systems, with project responsibility and inspection assigned.
Installation support for fire-protective linings and insulation on walls, slabs and technical elements under a specified system.
Complementary service · no individual brochure yetApproved boards and insulation; interfaces and edge details; agreed photo records.
Fire resistance and classification follow the documented system and appointed designer.
Share your site, drawings, quantities and programme. We can discuss a clear package and its interfaces.
Enquire about this work ↗Partition systems, suspended ceilings, shielding linings and acoustic joint details in specialist environments.
Structural, fire and acoustic performance comes from the project design and approved system.
Bring partitions, shaft walls and technical linings together with the installations they surround. Metal framing, insulation, board layers and perimeter details are coordinated before closing. X-ray shielding follows the specialist design and acceptance…
Partitions, linings, service zones and specified X-ray shielding boards where required
Shielding and fire performance follow the appointed designer and specified systems.
Make the ceiling work with lighting, ventilation and maintenance access. We coordinate set-out, supporting systems, perimeter seals and service openings so the visible finish and the technical zone can be handed over together.
Ceiling modules, access hatches, service coordination and perimeter details
Structural, fire and acoustic performance comes from the project design and approved system.
Connect architectural intent with practical installation. Timber wall and ceiling packages focus on module alignment, substructure, edges, service integration and the specified acoustic and fire properties.
Acoustic panels, timber linings, support frames and neat edge details
Structural, fire and acoustic performance comes from the project design and approved system.
Sealing joints and penetrations in sound-insulating wall and ceiling systems in accordance with specified acoustic details.
Complementary service · no individual brochure yetPerimeter and connection joints; service penetrations; coordinated drywall and MEP inspections.
Acoustic performance follows design criteria; no independent acoustic certification is claimed.
Share your site, drawings, quantities and programme. We can discuss a clear package and its interfaces.
Enquire about this work ↗Foundation preparation, concrete works, hollow-core slabs, precast erection and approved openings.
Structural design, lifting plans, temporary stability and access must be agreed before work.
Define a practical groundworks package covering excavation, trenches, formation levels and material handling. The sequence starts with ground information, existing utilities, safe access and the agreed temporary works.
Excavation and preparation; formwork and logistics under approved design
Geotechnical, structural and approval responsibilities stay with their appointed parties.
Coordinate deliveries, lifting and installation as a sequence of stable stages. Assembly scope, bearing levels, temporary bracing and connections follow the structural and erection design, with responsibilities agreed before mobilisation.
Precast elements, hollow-core slabs, erection sequence and temporary stability
Agreed lifting plans, temporary stability and structural approval are prerequisites.
Coordinate controlled openings for construction and service interfaces through a defined specialist cutting package. Work starts with approved positions, structural and utility clearance, access and containment, connecting diamond cutting or drilling with support, removal and the documented preparation of finished openings.
Approved cores and openings; dust/water control and safe removal
Cutting and drilling require structural release and concealed-service checks.
Share your site, drawings, quantities and programme. We can discuss a clear package and its interfaces.
Enquire about this work ↗Vapour barriers, airtight details, façade cladding, roofing interfaces and insulation systems.
Specified products and approved moisture/airtightness details govern the scope.
Create continuity at the details that matter: membrane laps, windows, wall bases and service penetrations. Work packages can include specified RAW PRO systems and compatible accessories, with checks before linings conceal the completed layer.
Membrane laps, corners, window junctions and service penetrations
Specified products and approved moisture/airtightness details govern the scope.
Installation support for ventilated façades: brackets and rails, specified insulation and weather barrier, metal or fibre-cement panels, and flashings around windows, corners and joints.
Brackets, façade frames, ventilated cavities, panels and edge details
Specified products and approved moisture/airtightness details govern the scope.
Connect roof work with the interfaces that control water management and buildability. We coordinate substrates, insulation, membrane sequencing, penetrations and edge details within the agreed roofing package, following the approved system and weather plan while maintaining access, protection and inspection before concealment.
Roof membranes, insulation, penetrations, edges and drainage interfaces
Water-tightness and warranties depend on the agreed system and responsibilities.
Treat externally insulated render façades as complete systems rather than interchangeable layers. We coordinate substrate acceptance, insulation boards, fixings, reinforced basecoat and finish with openings, plinths and weather conditions, following the approved ETICS specification and recording critical details before they are concealed.
ETICS elements, reinforced render, openings and plinth details
Specified products and approved moisture/airtightness details govern the scope.
Share your site, drawings, quantities and programme. We can discuss a clear package and its interfaces.
Enquire about this work ↗Openings, builders’ supports, routes and coordination with electrical, plumbing and ventilation trades.
No claim of Danish electrical, plumbing, gas or drainage authorisation. Restricted work belongs to authorised firms.
Duct routes, supports, penetrations and maintenance access, coordinated with other trades.
Builders’ routes, support details and maintenance access; no restricted HVAC connections
Restricted HVAC/plumbing installation is excluded without proper authorisation.
Plan pipe routes, supports, insulation and penetrations as part of one coordinated work area. The offer identifies installation responsibilities, testing and the authorised business responsible for any regulated work.
Pipe openings, supports and coordination; no restricted plumbing connections
Restricted plumbing work must be done by an authorised company.
Prepare the construction around electrical installations: recesses, board surrounds, reinforcement, openings and access. Coordination with the electrical contractor helps avoid rework and establishes checks before concealed zones are closed.
Openings, niches, reinforcing and builders’ works; no electrical connection works
No restricted electrical installation works are undertaken by Ædra.
Share your site, drawings, quantities and programme. We can discuss a clear package and its interfaces.
Enquire about this work ↗Flooring, decoration, doors, joinery, masonry and interior adaptation.
Materials, finish criteria and any specialist requirements must be agreed per package.
Bring the substrate, floor finish and adjoining trades into one planned package. We organise preparation, setting-out and installation interfaces for resilient, timber and tiled finishes, with attention to moisture, levels, movement joints and protection before the next work stage.
Substrates, moisture checks, thresholds, joints and finished-floor protection
Materials, finish criteria and any specialist requirements must be agreed per package.
Connect surface preparation with the finish the project requires. We organise filling, sanding, priming and painting of building surfaces, coordinating substrate condition, product compatibility, colour samples and access so that completed rooms can be inspected, protected and handed over in sequence.
Surface preparation, filling, primers and decorative finishes
Materials, finish criteria and any specialist requirements must be agreed per package.
Coordinate openings, frames and finished interfaces before installation begins. Door, window and joinery packages connect survey dimensions, support, fixings, perimeter seals and architectural finishes, with inspection points for operation, access and the documented requirements of the selected complete assembly.
Frames, door leaves, windows, perimeter seals and functional inspection
Materials, finish criteria and any specialist requirements must be agreed per package.
Plan complementary building works around substrate readiness and adjoining systems. Masonry partitions, render, plaster and tiled surfaces are coordinated through setting-out, reinforcement details, material compatibility, movement joints and finish inspections, with the agreed design controlling structural and moisture-related requirements.
Masonry, plaster and tiling; substrate, joints and wet-area interfaces
Materials, finish criteria and any specialist requirements must be agreed per package.
Bring several interior trades into a practical renovation sequence. We coordinate surveys, work-area release, partitions, finishes and service interfaces around the existing building, maintaining clear scope boundaries, inspection stages and protection so that completed areas can return to use in planned phases.
Interior reconfiguration, phased access and multi-trade coordination
Materials, finish criteria and any specialist requirements must be agreed per package.
Share your site, drawings, quantities and programme. We can discuss a clear package and its interfaces.
Enquire about this work ↗Trade coordination, site logistics, quality checks and selective non-structural strip-out.
No asbestos demolition without Danish company authorisation; suspected hazards require specialist assessment.
Keep the work packages connected through planning, supervision, inspection points and progress reporting. A shared view of interfaces, changes and outstanding items helps clients and contractors make decisions and prepare a documented handover.
Work fronts, daily coordination, QA checks and handover interfaces
No asbestos demolition without Danish company authorisation; suspected hazards require specialist assessment.
Prepare renovation areas through a controlled sequence of nonstructural removal and protection. We coordinate retained elements, service isolation interfaces, material surveys, separation and waste routes before removing agreed finishes or fittings, leaving recorded conditions and clear work fronts for the following construction trades.
Non-structural selective removal, material segregation and safe preparation
No asbestos or hazardous-material removal without authorised specialists.
Share your site, drawings, quantities and programme. We can discuss a clear package and its interfaces.
Enquire about this work ↗